SATO Printer Repair Service Oakland

SATO printer support in Oakland is what we offer. Below are some tips to support your SATO printers.

1. One of the greatest failures occurring in Sato thermal barcode printers is due to the printheads not
   being cleaned regularly. A good rule of thumb is to clean the printhead on each of your Sato thermal
   printers every time you replace a ribbon or roll of paper. It takes only about a minute and this
   action could save you thousands of dollars over the life of the printer. Follow the instructions in
   your User’s Manual as to the type of cleaning solvent to be used for your specific model.
2. If you feel you are burning out printheads too often on your Sato thermal printer, you may want to
   check your User’s Manual for the recommended heat and darkness settings. An incorrect
   setting often will reduce the printhead life and could cost you thousands of dollars over the life of
   the printer.
3. Dust residing on the Media Sensor can cause major service issues. The Media Sensor is the
   mechanism that insures that the gap between the paper and the printhead remains constant.
   Most people purchase a bottle of “canned air” and simply give the Media Sensor a few quick
   blasts of air, which will usually clear out any dust residue left over from the roll paper. You
   should consider doing this regularly, every time you change the ribbon or a roll of paper. It will
   only take a few seconds and it will ensure more up-time.
4. If you are using a ribbon in your Sato thermal printer, be sure that it is a good quality ribbon. Lower
   cost ribbons are often not manufactured to the exact wax and/or resin specifications of your
   printer and could cause a wax build-up on the platen. Wax build-up can cause poor print quality
   resulting in barcode reliability issues.
5. If you are using a Sato thermal printer that does not use a ribbon (typically called a Direct Thermal
   printer vs. a Thermal Transfer printer that does use ribbons) and you are constantly having
   problems with defective printheads, you may want to consider either changing your printer to a
   Thermal Transfer printer or using a better quality paper. A Thermal Transfer printer, due to the
   position of the ribbon between the printhead and the label paper, can greatly extend the life of
   thermal printheads, as paper is not directly rubbing against the printhead itself and causing
   friction.
6. A good rule of thumb, when purchasing new ribbons on Sato thermal transfer printers, is to purchase
   a ribbon that is slightly wider than the actual labels that you are using. For instance, if the label
   that you are using is 4.1″ in width, then you may want to consider purchasing ribbons that are
   4.33″ in width.
7. Are you wearing out printheads? If so, here is something you may want to check. Be sure that
   you are not using low grade label paper if you are using Direct Thermal printers. Often bargain
   priced rolls of paper really are not a “bargain”. Why? Because low grade paper often is coarser
   and can cause more wear on the printheads. We have seen situations with even as high as
   50% more wear on the printhead. As you may know, printheads in thermal printers are very
   expensive. It may make sense to pay a little more for paper, as it is a fraction of the cost
   compared to replacing printheads more often. Remember, the manufacturers of thermal
   printers consider the printheads as consumables that the end-user is responsible to replace.
   These consumables run into the hundreds of dollars each.
8. Do you have burned-out printhead elements on your thermal printer? Here is how to tell with a
   PAUSE TEST. There may be situations where it looks like information is missing on your labels
   and/or barcodes when they are being printed. There is always a chance that one or more of the
   print elements in your thermal printer printhead may be burned out. Before calling someone for
   Sato thermal printer repair, you may want to try this simple test that only takes a few moments to see
   if in fact it is your print elements. Keep in mind that some manufacturers considers printheads
   as consumables and they must be replaced from time to time. Typically, this is performed by a
   qualified Sato printer repair technician. This self test can be used to print test labels when you make
   adjustments to the thermal printer’s mechanical assemblies to determine if any of the printhead
   elements are not working.
9. What are printer and print server alerts? Should you pay attention to them? Alerts give you the
   ability to proactively manage your Sato thermal printer and print server. If the printer or print server
   has an error, you would be sent an alert notifying you of the situation. The manufacturer Sato
   uses SatoNet Bridge that gives you control to monitor your bar code printers from anywhere,
   and documents the alerts to a log file. A soon as SatoNet Bridge receives an alert, the alert
   appears in the Events tab. If you have not viewed the alert yet in the Events tab, the box in the
   status bar at the bottom of the application shows:

    New alert
    Alert type
    Alert severity by color

   You can configure SatoNet Bridge to notify you by blinking the application tab in the task bar.
   Remember, SatoNet Bridge only logs alerts that occur while the application is running. A good
   Sato repair company sees this issue often and will be able to supply you with a new Sato
   printhead and will also fully check out your Sato printer. A steady program that includes Sato
   printer maintenance will help you keep your printer up and running longer. Check with the
   manufacturer of your thermal printer to see what they offer to manager your thermal printer.

10. Clean the exterior and interior area of your Sato thermal printer often. To keep your Sato thermal printer
    running optimally, remember to clean the interior and exterior of the printer. When these areas
    are dirty, the chance of debris getting into the wrong area is increased. To clean the exterior
    surfaces of the printer use a lint-free cloth. Do not use harsh or abrasive cleaning agents or
    solvents. If necessary, a mild detergent solution or desktop cleaner may be used sparingly. You
    should inspect the interior area after every four rolls of media. Remove any dirt and lint from the
    interior of the printer using a soft bristle brush and/or vacuum cleaner. A good Sato thermal printer
    repair company sees this issue often and will be able to supply you with a new Sato thermal printer
    printhead and will also fully check out your Sato thermal printer. A steady program that includes
    Sato thermal printer maintenance will help you keep your Sato thermal printer up and running longer.

1. One of the greatest failures occurring in Sato thermal barcode printers is due to the printheads not
   being cleaned regularly. A good rule of thumb is to clean the printhead on each of your Sato thermal
   printers every time you replace a ribbon or roll of paper. It takes only about a minute and this
   action could save you thousands of dollars over the life of the printer. Follow the instructions in
   your User’s Manual as to the type of cleaning solvent to be used for your specific model.
2. If you feel you are burning out printheads too often on your Sato thermal printer, you may want to
   check your User’s Manual for the recommended heat and darkness settings. An incorrect
   setting often will reduce the printhead life and could cost you thousands of dollars over the life of
   the printer.
3. Dust residing on the Media Sensor can cause major service issues. The Media Sensor is the
   mechanism that insures that the gap between the paper and the printhead remains constant.
   Most people purchase a bottle of “canned air” and simply give the Media Sensor a few quick
   blasts of air, which will usually clear out any dust residue left over from the roll paper. You
   should consider doing this regularly, every time you change the ribbon or a roll of paper. It will
   only take a few seconds and it will ensure more up-time.
4. If you are using a ribbon in your Sato thermal printer, be sure that it is a good quality ribbon. Lower
   cost ribbons are often not manufactured to the exact wax and/or resin specifications of your
   printer and could cause a wax build-up on the platen. Wax build-up can cause poor print quality
   resulting in barcode reliability issues.
5. If you are using a Sato thermal printer that does not use a ribbon (typically called a Direct Thermal
   printer vs. a Thermal Transfer printer that does use ribbons) and you are constantly having
   problems with defective printheads, you may want to consider either changing your printer to a
   Thermal Transfer printer or using a better quality paper. A Thermal Transfer printer, due to the
   position of the ribbon between the printhead and the label paper, can greatly extend the life of
   thermal printheads, as paper is not directly rubbing against the printhead itself and causing
   friction.
6. A good rule of thumb, when purchasing new ribbons on Sato thermal transfer printers, is to purchase
   a ribbon that is slightly wider than the actual labels that you are using. For instance, if the label
   that you are using is 4.1″ in width, then you may want to consider purchasing ribbons that are
   4.33″ in width.
7. Are you wearing out printheads? If so, here is something you may want to check. Be sure that
   you are not using low grade label paper if you are using Direct Thermal printers. Often bargain
   priced rolls of paper really are not a “bargain”. Why? Because low grade paper often is coarser
   and can cause more wear on the printheads. We have seen situations with even as high as
   50% more wear on the printhead. As you may know, printheads in thermal printers are very
   expensive. It may make sense to pay a little more for paper, as it is a fraction of the cost
   compared to replacing printheads more often. Remember, the manufacturers of thermal
   printers consider the printheads as consumables that the end-user is responsible to replace.
   These consumables run into the hundreds of dollars each.
8. Do you have burned-out printhead elements on your thermal printer? Here is how to tell with a
   PAUSE TEST. There may be situations where it looks like information is missing on your labels
   and/or barcodes when they are being printed. There is always a chance that one or more of the
   print elements in your thermal printer printhead may be burned out. Before calling someone for
   Sato thermal printer repair, you may want to try this simple test that only takes a few moments to see
   if in fact it is your print elements. Keep in mind that some manufacturers considers printheads
   as consumables and they must be replaced from time to time. Typically, this is performed by a
   qualified Sato printer repair technician. This self test can be used to print test labels when you make
   adjustments to the thermal printer’s mechanical assemblies to determine if any of the printhead
   elements are not working.
9. What are printer and print server alerts? Should you pay attention to them? Alerts give you the
   ability to proactively manage your Sato thermal printer and print server. If the printer or print server
   has an error, you would be sent an alert notifying you of the situation. The manufacturer Sato
   uses SatoNet Bridge that gives you control to monitor your bar code printers from anywhere,
   and documents the alerts to a log file. A soon as SatoNet Bridge receives an alert, the alert
   appears in the Events tab. If you have not viewed the alert yet in the Events tab, the box in the
   status bar at the bottom of the application shows:

    New alert
    Alert type
    Alert severity by color

   You can configure SatoNet Bridge to notify you by blinking the application tab in the task bar.
   Remember, SatoNet Bridge only logs alerts that occur while the application is running. A good
   Sato repair company sees this issue often and will be able to supply you with a new Sato
   printhead and will also fully check out your Sato printer. A steady program that includes Sato
   printer maintenance will help you keep your printer up and running longer. Check with the
   manufacturer of your thermal printer to see what they offer to manager your thermal printer.

10. Clean the exterior and interior area of your Sato thermal printer often. To keep your Sato thermal printer
    running optimally, remember to clean the interior and exterior of the printer. When these areas
    are dirty, the chance of debris getting into the wrong area is increased. To clean the exterior
    surfaces of the printer use a lint-free cloth. Do not use harsh or abrasive cleaning agents or
    solvents. If necessary, a mild detergent solution or desktop cleaner may be used sparingly. You
    should inspect the interior area after every four rolls of media. Remove any dirt and lint from the
    interior of the printer using a soft bristle brush and/or vacuum cleaner. A good Sato thermal printer
    repair company sees this issue often and will be able to supply you with a new Sato thermal printer
    printhead and will also fully check out your Sato thermal printer. A steady program that includes
    Sato thermal printer maintenance will help you keep your Sato thermal printer up and running longer.

Here are some of the surrounding cities in Oakland we service:
94501 Alameda, CA Alameda 510
94502 Alameda, CA Alameda 510
94505 Discovery Bay, CA Contra Costa 510
94525 Crockett, CA Contra Costa 510
94530 El Cerrito, CA Contra Costa 510
94536 Fremont, CA Alameda 510
94537 Fremont, CA Alameda 510
94538 Fremont, CA Alameda 510
94539 Fremont, CA Alameda 510
94540 Hayward, CA Alameda 510
94541 Hayward, CA Alameda 510
94542 Hayward, CA Alameda 510
94543 Hayward, CA Alameda 510
94544 Hayward, CA Alameda 510
94545 Hayward, CA Alameda 510
94546 Castro Valley, CA Alameda 510
94547 Hercules, CA Contra Costa 510
94548 Knightsen, CA Contra Costa 510
94552 Castro Valley, CA Alameda 510
94555 Fremont, CA Alameda 510
94557 Hayward, CA Alameda 510
94560 Newark, CA Alameda 510
94564 Pinole, CA Contra Costa 510
94569 Port Costa, CA Contra Costa 510
94572 Rodeo, CA Contra Costa 510
94577 San Leandro, CA Alameda 510
94578 San Leandro, CA Alameda 510
94579 San Leandro, CA Alameda 510
94580 San Lorenzo, CA Alameda 510
94587 Union City, CA Alameda 510
94601 Oakland, CA Alameda 510
94602 Oakland, CA Alameda 510
94603 Oakland, CA Alameda 510
94604 Oakland, CA Alameda 510
94605 Oakland, CA Alameda 510
94606 Oakland, CA Alameda 510
94607 Oakland, CA Alameda 510
94608 Emeryville, CA Alameda 510
94609 Oakland, CA Alameda 510
94610 Oakland, CA Alameda 510
94611 Oakland, CA Alameda 510
94612 Oakland, CA Alameda 510
94613 Oakland, CA Alameda 510
94614 Oakland, CA Alameda 510
94615 Oakland, CA Alameda 510
94617 Oakland, CA Alameda 510
94618 Oakland, CA Alameda 510
94619 Oakland, CA Alameda 510
94620 Piedmont, CA Alameda 510
94621 Oakland, CA Alameda 510
94622 Oakland, CA Alameda 510
94623 Oakland, CA Alameda 510
94624 Oakland, CA Alameda 510
94649 Oakland, CA Alameda 510
94659 Oakland, CA Alameda 510
94660 Oakland, CA Alameda 510
94661 Oakland, CA Alameda 510
94662 Emeryville, CA Alameda 510
94666 Oakland, CA Alameda 510
94701 Berkeley, CA Alameda 510
94702 Berkeley, CA Alameda 510
94703 Berkeley, CA Alameda 510
94704 Berkeley, CA Alameda 510
94705 Berkeley, CA Alameda 510
94706 Albany, CA Alameda 510
94707 Berkeley, CA Alameda 510
94708 Berkeley, CA Alameda 510
94709 Berkeley, CA Alameda 510
94710 Berkeley, CA Alameda 510
94712 Berkeley, CA Alameda 510
94720 Berkeley, CA Alameda 510
94801 Richmond, CA Contra Costa 510
94802 Richmond, CA Contra Costa 510
94803 El Sobrante, CA Contra Costa 510
94804 Richmond, CA Contra Costa 510
94805 Richmond, CA Contra Costa 510
94806 San Pablo, CA Contra Costa 510
94807 Richmond, CA Contra Costa 510
94808 Richmond, CA Contra Costa 510
94820 El Sobrante, CA Contra Costa 510
94850 Richmond, CA Contra Costa 510